Military Wiki
Register
Advertisement
Tank, Cruiser, Mk II (A10)
CruiserMk2
Type Cruiser tank
Place of origin Flag of the United Kingdom United Kingdom
Service history
In service 1940-1941 [1]
Used by British Army
Wars Second World War
Production history
Designer Sir John Carden
Designed 1934
Manufacturer Vickers and others
Produced 1938-1940 [1]
No. built 175
Specifications
Mass 14.3 tonnes
Length 18 ft 4 in (5.5 m)
Width 8 ft 4 in (2.6 m)
Height 8 ft 8 in (2.5 m)
Crew 5 (Commander, loader, gunner, driver, Hull MG gunner)

Armour 6 - 30 mm
Main
armament
OQF 2pdr
100 rounds
Secondary
armament
two Vickers/BESA Machine guns
4,050 rounds
Engine AEC Type A179 6-Cylinder Petrol
150 hp
Suspension triple wheel bogie with coil spring
Operational
range
100 miles (road)
Maximum speed 16 mph (road)
8 mph (off-road)

The Tank, Cruiser, Mk II (A10), was developed alongside the A9, and was intended to be a heavier, infantry tank version of that type. In practice it was not deemed suitable for the infantry tank role and was classified as a "heavy cruiser".

History and specifications[]

The A10 was developed by Sir John Carden of Vickers in 1934 by adaptation of his A9 design. The A10 specification called for armour of up to 1 inch standard (the A9 was 14mm); a speed of 10 mph was acceptable.[2] The two sub-turrets present on the A9 were removed, and extra armour bolted onto that already present on the front and sides of the hull, along with all faces of the turret, providing approximately twice the armour in most areas. The A10 was two tonnes heavier than the A9, but used the same 150 bhp engine, and as a consequence the tank's top speed was cut from 25 mph to 16 mph.

The turret armament consisted of a QF 2-pounder (40mm) gun and a coaxial .303 Vickers machine gun. For the production version there was a 7.92mm BESA machine gun mounted in the hull in a barbette to the right of the driver. This was added to give extra firepower but at the expense of simplicity - the Vickers and the BESA using different ammunition. The tank had a total crew of five (Commander, gunner, loader, driver and hull machine gunner), and there was no separation between the driver's compartment and the fighting compartments. The prototype ("Tank, Experimental A10E1") was completed in 1936, a few months after the A9 prototype. Carden had died in an air crash in 1935 and development was slower than expected. In 1937 the A10 was dropped as an infantry support but in 1938 it was decided to produce it as a "heavy cruiser". The A10 was accepted for service - initially as "Tank, Cruiser, Heavy Mk I" and then "Tank, Cruiser A10 Mk 1" and finally "Tank, Cruiser Mk II". Production was ordered in July 1938. Total production was 175 vehicles including the 30 CS versions (see below), 45 were built by Birmingham Railway Carriage and Wagon Company, 45 by Metropolitan-Cammell, 10 by Vickers. In late 1939 another order was placed with Birmingham Railway Carriage and Wagon Company, this time it was a larger order of 75 vehicles. - entering service in December 1939, but was something of an oddity - it had been intended to sacrifice speed for armour like an Infantry tank, but was still relatively poorly armoured, and was, as a result, not effective.

Combat history[]

Bundesarchiv Bild 101I-161-0317-26, Balkan, Griechenland, britischer Panzer

A British Cruiser Mk II disabled by having lost a track (seen lower right) in Greece, 1941.

A number of Mark IIs were part of the British Expeditionary Force (BEF) sent to France in the early stages of World War II. Their cross country performance was recorded as poor, but they were still used later in North Africa at the defence of Tobruk in 1941, where reliability and suspension performance in the desert conditions was praised. Sixty worn out examples were taken to Greece by the 3rd Royal Tank Regiment and, although they performed well against the German tanks, over 90% were lost due to mechanical breakdowns as opposed to enemy action (mainly lost tracks).[3][4]

Variants[]

Tank, Cruiser, Mk II (A10 Mk I)[]

Classified as a 'heavy cruiser' and 31 were sent to France with the 1st Armoured Division, but performed poorly in the following campaign. Also served in the North African Campaign until late in 1941.

Tank, Cruiser, Mk IIA (A10 Mk IA)[]

The coaxial Vickers machine guns were replaced with BESA machine guns. Armoured radio housing added.

Tank, Cruiser, Mk IIA CS (A10 Mk IA CS)[]

Cruiser MkIIA CS 1 Bovington

Cruiser MkIIA CS

Had a 3.7" (94 mm) howitzer in the turret instead of the 2 pdr. The standard ammunition load was 40 rounds smoke, and a few HE shells. The CS denotes Close Support.

This weapon was derived from a World War I field howitzer. It was not related to the 3in howitzer used in later British tanks in World War II, which was itself replaced by a 95mm howitzer in the later versions of the Churchill infantry tanks and all CS versions of the Centaur and Cromwell cruiser tanks. British doctrine was that the CS tank was to provide smoke cover in advances or retreats and hence many more smoke rounds were carried than HE.[5]

Other vehicles based on chassis[]

References[]

Notes
  1. 1.0 1.1 *Forty, George; Jack Livesy (2006). The World Encyclopedia of Tanks & Armoured Fighting Vehicles. Lorenz Books. pp. 55. ISBN 978-0-7548-1741-3. 
  2. AFV Profile No. 6 p2
  3. Robert Crisp, Brazen Chariots (W.W. Norton & Co. 2005), at 15.
  4. "A Tankie's Travels" By Robert Watt ISBN 1-84683-021-4
  5. Bovington accession record
Bibliography

External links[]


All or a portion of this article consists of text from Wikipedia, and is therefore Creative Commons Licensed under GFDL.
The original article can be found at Cruiser Mk II and the edit history here.
Advertisement